dpstar Group constantly strives to provide superior quality and highly reliable products at competitive prices for all our clients and dealers. As a result, we have built a proud reputation for being one of the largest heater manufacturer in Malaysia.
Tubular Heaters is also a CE certified product in our company.Our application is for heating almost any liquid or viscous materials including acids, water, synesthetic oils, lube oils as well as air, gases, steam or low melting point solids.The standard element consists of an 80/20 nickel chrome resistance wire which is connected to terminal pins, and centered in a metal tube. The tube is filled with high quality magnesium oxide and compressed to ensure a rapid heat transfer. The terminal pins from a non-heated section of the element well as the terminal arrangement. They are insulated from the tube by ceramic bushes. Kilowatt rating and voltage can be varied to suit each application.Our tubular heating element from the basis of all product in this catalog. They are manufactured from high quality materials in various sheath diameters. They can be supplied straight or bent to customers’ requirement.
Here is the selection of sheath and application for our dpstar tubular heaters :
COPPER
Heating of fresh water free from chlorine or other aggressive chemicals.
Copper element may nickel plated to provide protection in certain applications. Maximum sheath temperature in water 180*C.
INCOLOY 800 / 840
A nickel chrome alloy used for heating liquids where resistance to stress corrosion is required.
Maximum sheath temperature 850*C.
STAINLESS STEEL 304
Heating gases, where oxidization of corrosion is likely. Selection will depend on the media to be heated and the operating conditions. Maximum sheath temperature 750*C.
STAINLESS STEEL 316
Heating liquids where corrosion is likely. Selection will depend on the media to be heated and the operating conditions. Maximum sheath temperature 750*C.
TITANIUM
Heating aggressive liquids where other metal sheated materials do not have the required corrosion resistance.
Selection will depend on the chemical composition of the media to be heated. Maximum sheath temperature 500*C.
Our dpstar triple immersion heaters are designed with various sheath ratings to suit heating of most grades of oil, alkaline - cleaning solutions and water.Special wattage's in around 1500-12000 as for our voltages it is 240/415. As for our lengths and diameters it can be supplied upon customer’s request. Being a good heater manufacturer in Malaysia we are using a 304 Stainless Steel Heating Element
dpstar Ceramic Bobbin Heaters are for indirect heating of liquids and gases where the element is fitted into a pocket in the process tank or system. These are installed in larged storage tanks so that the element may be replaced without draining down the system or vessel. Also our Ceramic Bobbin Heater consists of 80/20 nickel chrome resistance wire supported on refractory insulators and connected to a terminal block at one end. The element flex to allow easy installation and handling. They are normally manufactured for horizontal mounting, but may be specially designed constructed for vertical installation. dpstar heater manufacturer in Malaysia made a Ceramic Bobbin Heater for any voltage or wattage within manufacturing limits. Heater can be supplied with suitable mild steel or stainless steel pockets and mounting flanges or bosses is required.
dpstar Ceramic Band Heaters offer heater longer life , high processing temperature capabilities and full flexibility for easy installation. dp star one of the major leading manufacturer and top supplier is able to provide high quality long life and use less wattage of ceramic band heaters(because of insulation) in plastics extrusion and injection molding applications. These band heaters are constructed with a stainless steel shroud enclosing high quality ceramic knuckles through which run coiled high temperature nickel-chromium element wire. The design features are as follows :
-Energy efficient , less power consumption
-High temperature capability up to 1600°F(875°C)
-Thermally insulated
-Uniform temperature
-Flexible, easy to install and remove
-Elongation compensation w/spring loaded screw over 18″diameter
Our dpstar Flexible Silicon Rubber Heaters is able to resist chemicals,moisture and abusive treatment. Furthermore being one of the top heater manufacturer in Malaysia the conditions to rapid heat-up , also to maintain the stability of termperature and uniform heat distribution. Furthermore it is also compatible with large environments due to the moisture and chemical resistant, also it is an exclusive hazardous-area rated heater. The durability of our product is exceptional because it is a multi-stranded resistance wire. Our order also comes with various complex shapes and also it is pack with controlling options installed.
Being the best heater manufacturer in Malaysia our drum heaters have an outstanding heating source to heat up any drum,pail,barrel and other containers of different sizes. Our band style heater can be apply almost to any material. Not forgetting the uniformed heat prevents scorching or degradation of the contents inside. The internal liquid should be placed above the silicone rubber band heater.Our spring locks is very easy to use that makes the movement of the band when liquid level fluctuate. Electric heating by either 1,2 & 3 can perform the maintenance and also the heating of temperature towards the drum.
The pencil heaters are fabricated in compliance with the international standards using high grade raw materials that are obtained from the reliable sources of the industry. Offered in varied specifications as per the requirements of the clients, these Pencil Heaters are renowned for features such as sturdiness, perfect finish, low maintenance and durable finish standards. Our heating elements are the best made in Malaysia.
Backersafe Immersion Heaters are manufactured to the latest legislation of BSEN60335-2-73. Two specific clauses within this specification are aimed at eliminating the risk of boiling water. The most significant requirement is that the immersion heater be isolated from the mains supply should the primary thermostat fail with the contacts closed which would allow the water to reach a temperature in excess of 85 degrees centigrade.The ‘Backersafe’ Immersion heaters are manufactured in a full range of sheath material including copper, incoloy 800, incoloy 825 and titanium to suit the varying water conditions around the country.
Daiichi Denko Anti-Condensation Heater As now dpstar is standing is because of our heating elements are so great. Anti-condensation heater is designed to maintain the temperature inside of an enclosure several degrees above surroundind ambient temperature and above the dew point.
Radiant Panel Heaters is made by our top best heater manufacturer in Malaysia. Firstly the heater can be mounted to radiate in any direction. Also our heater is reliable because there is no reduction in radiant output over life of heater. Uniform Radiation Pattern Assured with a wide flat infrared surface versus the line pattern given in normal radiant heaters. This eliminates uneven heating of the work and allows uniform heating of a stationary surface such as in an indexing process. Also external reflectors are not required, the refractory board and bulk insulation behind the heating element help prevent back heat loss. It is a one-piece bonded construction resists damage from vibration and shock.
Flange Immersion heaters can be designed with any element length, wattage and voltage. High purity compacted Mg0 powder provides maximum heat conductivity and optimum dielectric strength.Flange Immersion Heaters come in a wide variety of configurations, styles, and shapes. Our goal is to create a simple yet effective design to solve any fluid.
Bends are recompaced to restore Mg0 density. Thermocouples can be installed for high limit temperature control. Spacers installed on elements to assist flow distribution.
Circulation Heaters compact heating systems for fluids and gases. These heaters are ideal for applications such as purified and inert gases, supercritical fluids and liquids like de-ionized water for use in semiconductor and electronics industries as well as for general liquid and gas heating applications.Circulation heaters, also referred to as “in-line heaters” are used for heating flowing liquids and gases.Non-pressurized or highly pressurized fluids can be heated very effectively using either direct or indirect circulation heating. A wide variety of standard designs and custom engineered power ratings, sizes, flow capacities and options are available to fulfill most any application needs.
Finned Air Heaters are normally used for forced convection heating with outlet air temperatures of 300°C (572°F) or less. Steel finned heaters are standard with surface temperatures limited to about 425°C (797°F) compared to 815°C (1500°F) for an alloy sheathed non-finned heater.The finned air heater is designed for use in natural and forced convection space heating, our range of finned air heaters are suitable for increased heat transfer surface area and where higher wattage is required. Featuring rugged construction, these finned heaters can be used in a multitude of industrial environments. Finned tubular heaters are used for forced convection heating, air or gas heating systems. They are customized to meet your specific application needs. It is also UL certified.
dpstar duct heaters are ideal solutions for a variety of applications, including space heating, primary heating, secondary heating auxiliary heating, reheating, or multizone and variable air volume heating. dpstar uses proprietary software packages to specify coils and wiring configurations, sheet metal, element support racks, controls, options and accessories.
Our cartridge heaters are most frequently used for heating metal parts by insertion into drilled holes. For easy installation, the heaters are made slightly undersize relative to their nominal diameter.Our Cartridge Heaters are largely demanded by our clients spread all over the world. dpstar cartridge heaters are swaged designs, made for use in applications where high watt density, high temperatures and long service life are critical to minimize mold service downtime and expensive press open time. The swaged construction produces a highly compacted unit that resists shock and vibration, while providing for maximum element life through efficient transfer heating. They last up to 20 times longer than uncompacted cartridge heaters.
dpstar designs cast-in heaters of aluminum and bronze for various heating applications in industries, such as Semiconductor and Plastics Processing, Packaging Machinery, Foodservice, Paper Processing, Hot Melt Adhesives, Medical Equipment, Heat Transfer Presses and Textile Manufacturing. dpstar is widely recognized as the industry leader in manufacturing Cast-In heater/coolers for the plastics industry, our capabilities and the application possibilities for utilizing Cast-In Heater Technology extend far beyond the scope of plastics machinery.
Black Infrapara Ceramic Heaters is a unique ceramic heater with selected ceramics with high thermal durability, mechanical strength and good electrical insulation. High quality Nichrome wire is used too. It is also High emissivity ,Quick thermal response and high thermal efficiency.Not forgetting it is easy control to radiate favourable wave lengths for different target materials. The speed of our cermaic heater is 1-10 times more speedy than ordinary heaters. Together with uniform temperature distribution. The electric power may be saved up to 50%, production yield may be raised 30% up.Oven volume reduceable to one half or even less.Maintenance or replacement of existing old-fashioned heat pipes in ovens is easy. It is also free from dust contamination. No fire flame appears during heating process and high safety assured.
Infrared Silica Quartz Heaters are straight long wave infrared rays can be easily arranged to fall on an object by use of a reflection plate. If the cross-section of the reflection plate is designed in parabolic shape, most of the reflected rays will go in parallel direction to heat the object.Aluminum plate has excellent reflective power, Stainless plate is slightly inforior to aluminum plate while stainless plate must be used where corrosive gas emerges.There is 30% difference between the use of parabolic reflection plate and a plane type. Therefore a parabolic reflection plate should be used whenever it is possible.For maintaining the efficiency of the reflector cleaning must be done. It goes the same with infrared quartz heaters.
Ceramic elements produced by Maltec H that is our heater manufacturer in malaysia that includes ceramic through elements, ceramic hollow elements, ceramic flat elements, and ceramic infrared bulbs.the Ceramic Infrared heating element, was created to maximize heater efficiency and performance while maintaining durability and design flexibility. These heaters are capable of transferring up to 90% of their input as radiant energy, and maximum efficiency is reached when the emitted wavelength and the absorption spectrum of the material to be heated are optimized.
We are the heater manufacturer that makes heating elements easier and more advance to use. Mineral Insulated Heating Cable Mineral insulated heating cables, as well as complementary self regulating heating cables, provide the best performance in the area of electrical heat tracing for building and industrial applications. dpstar mineral insulated heater is a thin, responsive heater that uses the most advanced heater construction techniques. A nickel-chromium element wire is embedded in dpstar exclusive mineral insulation material, which has a much higher thermal conductivity than the mica and hard ceramic insulators used in conventional heaters. This thin layer of insulation brings the element wire closer to the heater sheath. The result is heat flows easily from the element wire to the sheath allowing the wire to run cooler than conventional heaters and increasing heater life.
Quartz Immersion Heaters Units can be ordered in different combinations such as: Complete Heater, Heater Less Guard, or each piece individually. Materials include steel, stainless steel, titanium and quartz. Teflon coated is also available as well as protective guards for some models. Single and multiple coil, loop and tube configurations are available.
The inclusion of modern equipment and sophisticated technology had made our company to be much faster and efficient. For more information you can visit our website at our home page.
Tuesday 7 July 2015
Monday 29 June 2015
Temperature Controller
Our customers can find a variety of Temperature Controllers. These applications are used in various industries for monitoring the temperature. It compares the actual temperature to the required control temperature and provides an output to a control element. Shimaden is one of dpstar best temperature controller and at a very low cost compare to others in the market. Also dpstar is the top manufacturer and supplier in Malaysia . Please visit our website to get more information.
RTD Sensor
RTDs have broad temperature ranges, are less susceptible to EMF resistance, vibration and temperature shock. They provide excellent long term stability and are available in small dimensions. dpstar is one of the greatest manufacturer and supplier in Malaysia. dpstar RTD sensors are highly accurate and fast responding sensing elements. They utilize the direct relationship between resistance and temperature to provide repeatable and measurable results. Visit our website for more info.
Heating element
Heater elements within electric heaters are mainly composed of three elements: an insulating core, a heat conductive coil wrapped around the insulation and an encasing sheath made from stainless steel, aluminum, nickel or iron. Insulating cores are necessary in most types of electric heaters to retain and absorb electrical energy so that it might be released as heat energy by surrounding coils or materials. Coiled wire heater elements, such as those used as household dryer heating elements, have no insulating core but transfer heat directly to the air through blown convection. In higher heat applications, cores are responsible for converting electrical energy into heat energy and are heating elements’ major component. Heater element cores are generally made from either NiChrome, a high resistance 80% nickel 20% chromium compound, or from a Positive Thermal Coefficient ceramic, which is a highly heat resistant barium titanate/lead titanate composite. Ceramics and NiChrome are by far the most common insulation materials, although various heater elements may use mineral insulation such as magnesium oxide, mica or fiberglass, depending on the heater’s application requirements. dpstar is the leading supplier and manufacturer in Malaysia. Come and get more info now .
Thermocouple
A thermocouple is a temperature measurement sensor consisting of two dissimilar metals joined together at one end.
Thermocouple wire is used in a thermocouple from the sensing point to the cold junction compensation point (or reference point). It is the difference in the millivolt output from the sensing point to the reference point that provides the temperature measurement.
Different thermocouple types require different alloy wire combinations. Some of the more popular thermocouple wire & cable types include type E (Chromel/Constantan), Type J (Iron/Constantan), Type K (Chromel/Alumel), and type T (Copper/Constantan).
dpstar is the greatest manufacturer and supplier in Malaysia. Come visit us at our website.
Thermocouple wire is used in a thermocouple from the sensing point to the cold junction compensation point (or reference point). It is the difference in the millivolt output from the sensing point to the reference point that provides the temperature measurement.
Different thermocouple types require different alloy wire combinations. Some of the more popular thermocouple wire & cable types include type E (Chromel/Constantan), Type J (Iron/Constantan), Type K (Chromel/Alumel), and type T (Copper/Constantan).
dpstar is the greatest manufacturer and supplier in Malaysia. Come visit us at our website.
Cartridge heater
dpstar cartridge heaters are swaged designs, made for use in applications where high watt density, high temperatures and long service life are critical to minimize mold service downtime and expensive press open time. The swaged construction produces a highly compacted unit that resists shock and vibration, while providing for maximum element life through efficient transfer heating. They last up to 20 times longer than uncompacted cartridge heaters. dpstar will also custom manufacture to your specifications. dpstar is one the top manufacturer and supplier in Malaysia. The best is to give us a visit at our website.
Immersion Heater
Immersion Heaters consist of tubular or heating elements immersed into the fluid. Immersion heaters are very efficient and cost effective since all energy that is generated is dissipated directly into the medium which is being heated. Immersion Heaters are used to heat fluids such as water, oil, chemical solutions, electro-plating and salt solutions. Since some of these fluids can be quit aggressive, the sheath material needs to be carefully chosen. dpstar is one the greatest manufacturer and supplier in Malaysia. Visit our website here.
Friday 26 June 2015
Cartridge Heater
There are many cartridge heater suppliers to choose from, but dpstar is a stocking cartridge heater supplier for your custom cartridge heater needs. We keep your special heating cartridges in stock to keep you out of trouble during emergency situations. dpstar is the top supplier and manufacturer in Malaysia. Visit our website for more info.
Heating elements
All applications that require heating elements must be controlled. To meet this requirement, dpstar provides control options ranging from bimetal thermostats to a network of digital PID temperature controllers for a heating system. dpstar is the greatest of all manufacturer and supplier in Malaysia. Give us a visit here.
RTD Sensor
Since many years we have been producing high-quality thermometer resistors Pt100 and etc that are the core of each RTD sensor. The unique technology combined with professional measuring equipment allow us to make high-class products. dpstar is the best manufacturer and supplier in Malaysia. Give us a visit .
Heating Element
Established in 1996, we dpstar are one of the leading manufacturer, supplier, distributor, exporter, importer and service provider of a huge array of Heating Element & Control Panel. Our offered product range are Industrial Heating Elements, Heating System, Ceramic Heater Parts and so on made using optimum quality of raw materials and highly technical machines and equipment for meeting high quality products. Our products is highly acknowledged among the clients for its dimensional accuracy, durability, corrosion resistance, and fine finishing. Visit us at our dpstar website.
Thermocouple
Thermocouples are among the easiest temperature sensors to use and obtain and are widely used in science and industry. They are based on the Seebeck effect that occurs in electrical conductors that experience a temperature gradient along their length. They are "simple", rugged, need no batteries, measure over very wide temperature ranges and more. They have their quirks, too, like everything else. The solution to thermocouple uses and problems lies in the details of a given application. dpstar is the south east asia biggest manufacturer and supplier in Malaysia. Visit us at dpstar.
Immersion Heater
Immersion heaters come in three basic types. All are supplied by Process Heating Services. If you click on the headings below, or the links at the bottom of the page, you will be able to view the ranges available.
- screwed immersion heaters, which are discussed in detail in our “What is an immersion heater” blog).
- flanged immersion heaters.
- over-the-side heaters, also known as VAT heaters.
dpstar is the best manufacturer and supplier in Malaysia. Pay us a visit at our website.
Thursday 25 June 2015
Temperature Controller
The role of the temperature controller is to measure the temperature on the thermometer, compare it to the set point and to calculate the amount of time the heater should remain switched on to maintain a constant temperature.
Many factors change the amount of time that the heater needs to maintain the process temperature. For example the size of the heater, the size of the oven, the amount of insulation surrounding the oven and the ambient temperature are some of the more obvious. But other factors such as the circulation of air within the oven, the humidity of the air. dpstar is the headmost manufacturer and supplier in Malaysia. For more info visit our website.
Many factors change the amount of time that the heater needs to maintain the process temperature. For example the size of the heater, the size of the oven, the amount of insulation surrounding the oven and the ambient temperature are some of the more obvious. But other factors such as the circulation of air within the oven, the humidity of the air. dpstar is the headmost manufacturer and supplier in Malaysia. For more info visit our website.
Immersion Heater
Industrial immersion heaters are a fast and efficient way of heating up various liquid solutions in processing equipment, large tanks and containers in many industries. Heating up liquids using direct heat transfer allows for the liquid medium to quickly reach the desired temperature using electric heating elements such as flanged heaters, screw plug heaters, over the side heaters or circulation heaters. dpstar is the best when it comes to being a manufacturer and supplier in Malaysia. Visit our website.
Cartridge Heater
dpstar cartridge heater may be used for many heating applications, but they are most often used to heat blocks of metal (such as dies on injection molding machines) by insertion into drilled holes in the metal. When used in this application, the major factors influencing heater lifetime are the watt density on the heater surface, the fit in the hole and operating temperature. dpstar is top manufacturer and heater in Malaysia. Visit our website for more info
Heating Elements
These heaters are available with heating elements made of copper, steel, stainless steel, cast iron, Incoloy, titanium, and PFA coated. A wide selection of kilowatt ratings, shapes and mounting methods are available to suit many different types of applications. dpstar is top manufacturer and supplier. Visit our site.
RTD Sensor
RTDs work on a basic correlation between metals and temperature. As the temperature of a metal increases, the metal's resistance to the flow of electricity increases. Similarly, as the temperature of the RTD resistance element increases, the electrical resistance, measured in ohms (Ω), increases. RTD elements are commonly specified according to their resistance in ohms at zero degrees Celsius (0° C). The most common RTD specification is 100 Ω, which means that at 0° C the RTD element should demonstrate 100 Ω of resistance. dpstar is the most amazing manufacturer and supplier in Malaysia. Visit us at dpstar.
Thermocouple
The thermocouple is based on the Seebeck effect, named after its discoverer, Thomas J. Seebeck. In its simplest form, the thermocouple consists of two wires of dissimilar metals or alloys joined at their ends, with a potentiometer (or a voltmeter) connected in one side of the circuit. The diagram shows such a thermocouple using wires of iron and constantan (an alloy of 60 per cent copper and 40 per cent nickel). dpstar is the leading manufacturer and supplier in Malaysia. You can visit our website here.
Wednesday 24 June 2015
Temperature Controller
Temperature Controllers fulfill temperature-dependent measurement, control, safety and monitoring tasks. Modern control technology, space-saving design and high operating comfort are particular advantages. dpstar the top manufacturer and supplier in Malaysia. Visit dpstar website now .
RTD Sensor
The advantages of using RTD's include:
•Linear over wide operating range
•Wide temperature operating range
•High temperature operating range
•Interchangeability over wide range
•Good stability at high temperature
dpstar the leading manufacturer and supplier only in Malaysia. Visit us at dpstar.
•Linear over wide operating range
•Wide temperature operating range
•High temperature operating range
•Interchangeability over wide range
•Good stability at high temperature
dpstar the leading manufacturer and supplier only in Malaysia. Visit us at dpstar.
Heating Element
We offer a vast selection of different heating elements, mostly bespoke to specific customer designs however some standard products are available within the key product groups. dpstar is the leading manufacturer and supplier throughout Malaysia. Visit our dpstar site.
Thermocouples
Thermocouples are classified with letters and are color coded. The most common types are J (black)-, K (yellow)- and T- (blue) type. The wire color indicates what type of thermocouple it is. (example: white + red wire insulations are used for J-type thermocouples; the colors of jacks and plugs for a J-type thermocouple is black. The greatest manufacturer and supplier in Malaysia. Visit at our dpstar web.
Cartridge Heater
A cartridge heater can also come in split cartridge heaters, which are split to enhance the design for even heat transfer. Depending on your application and project you may want to choose to go with a cartridge heater over a split cartridge heater. dpstar is one of the top manufacturer and supplier in Malaysia. Visit us at our website.
Immersion Heater
Immersion heaters are designed for vessels where through the side immersion heaters cannot be conveniently installed. These heaters are installed through the top of the vessel with the heated portion of the unit along the side or at the bottom of the tank. dpstar is the leader of manufacturer and supplier. Visit our website.
Tuesday 23 June 2015
Temperature Controller Info 3
Our comprehensive range of controllers enable you to choose from a vast range of products designed by a company with over 19 years of control expertise. dpstar is a terrific manufacturer and supplier in Malaysia. dpstar website here.
RTD Sensor Info 3
Resistance Temperature Detectors (RTD's) are stable and have a fairly wide temperature range, but are not as rugged and inexpensive as thermocouples. Since they require the use of electric current to make measurements, RTD's are subject to inaccuracies from self-heating.
An RTD capitalizes on the fact that the electrical resistance of a material changes as its temperature changes. RTD's rely on the resistance change in a metal. The resistance will rise more or less linearly with temperature. dpstar is the premium manufacturer and supplier in Malaysia . Visit us here .
An RTD capitalizes on the fact that the electrical resistance of a material changes as its temperature changes. RTD's rely on the resistance change in a metal. The resistance will rise more or less linearly with temperature. dpstar is the premium manufacturer and supplier in Malaysia . Visit us here .
Heating element Info 3
A typical heating element is usually a coil, ribbon, of strip of wire made from nichrome that gives off heat much like a lamp filament. When an electric current flows through it, it glows red hot and converts the electrical energy passing through it into heat, which it radiates out in all directions. Nichrome is an alloy (a mixture of metals and sometimes other chemical elements) that consists of about 80 percent nickel and 20 percent chromium (other compositions of nichrome are available, but the 80–20 mix is the most common). There are various good reasons why nichrome is the most popular material for heating elements: it has a high melting point (about 1400°C or 2550°F), doesn't oxidize (even at high temperatures), doesn't expand too much when it heats up, and has a reasonable (not too low, not too high, and reasonably constant) resistance (it increases only by about 10 percent between room temperature and its maximum operating temperature). dpstar is an outstanding manufacturer and supplier in Malaysia. For more info visit u at dpstar.
Thermocouple Info 3
Thermocouples are among the easiest temperature sensors to use and obtain and are widely used in science and industry. They are based on the Seebeck effect that occurs in electrical conductors that experience a temperature gradient along their length. They are "simple", rugged, need no batteries, measure over very wide temperature ranges and more. They have their quirks, too, like everything else. The solution to thermocouple uses and problems lies in the details of a given application. dpstar is the top leading manufacturer and supplier in Malaysia . Visit our site .
Cartridge Heater Info 3
Renowned for long trouble free service, cartridge heaters are constructed using sheaths of precision dimensions and tolerances for intimate contact with reamed holes. Internal heating elements are supported on high quality ceramic, solidly packed magnesium oxide with a wide variety of connections available, including plated steel screws and nuts or glass insulated nickel wires. Heating elements positioned close to the outside surface for maximum heat transfer, minimum core temperature, and faster heating. High watt-density units with stainless steel sheaths provide stable non-oxidising surfaces. dpstar is a leading manufacturer and supplier in Malaysia . For more info visit dpstar.
Immersion Heater Info 3
dpstar Corporation offers a broad line of immersion heaters for constant temperature baths and other processes that require the direct application of clean heat. dpstar immersion heaters are compact and highly customizable, allowing for maximum work area to reduce the amount of process chemicals consumed. dpstar immersion heaters heat efficiently and evenly for better temperature results. dpstar is a leading manufacturer and supplier in Malaysia . For more info visit us at dpstar.
Monday 22 June 2015
Temperature Controller
Temperature controllers are needed in any situation requiring a given temperature be kept stable. This can be in a situation where an object is required to be heated, cooled or both and to remain at the target temperature (setpoint), regardless of the changing environment around it. There are two fundamental types of temperature control; open loop and closed loop control. Open loop is the most basic form and applies continuous heating/cooling with no regard for the actual temperature output. It is analogous to the internal heating system in a car. On a cold day, you may need to turn the heat on to full to warm the car to 75°. However, during warmer weather, the same setting would leave the inside of the car much warmer than the desired 75°. dpstar is the best in Malaysia for manufacturer and supplier. Visit us here at dpstar.
RTD Sensor Info 2
Resistance Temperature Detectors (RTDs) have a linear increase in resistance as temperature rises. RTDs come in 2-wire, 3-wire or 4-wire versions. A 2-wire RTD signal is affected by the distance to the controller. 3-wire or 4-wire RTDs can compensate for line losses.
Thermocouples have two dissimilar metal wires joined at the hot junction. As temperature changes, a millivolt signal is read at the cold junction. The most common types of temperature thermocouples are Type J thermocouples and Type K thermocouples. Advantages of thermocouple sensors include: low cost, small size, wider temperature ranges and faster response than RTDs. The disadvantages of using thermocouples include: they are less linear and accurate than RTDs, a matching extension wire is needed, and thermocouples are sensitive to electrical noise.
dpstar is the leading manufacturer and supplier in Malaysia . Also Maltec-T is our very own manufacturer for RTD Sensor. Visit us here.
Thermocouples have two dissimilar metal wires joined at the hot junction. As temperature changes, a millivolt signal is read at the cold junction. The most common types of temperature thermocouples are Type J thermocouples and Type K thermocouples. Advantages of thermocouple sensors include: low cost, small size, wider temperature ranges and faster response than RTDs. The disadvantages of using thermocouples include: they are less linear and accurate than RTDs, a matching extension wire is needed, and thermocouples are sensitive to electrical noise.
dpstar is the leading manufacturer and supplier in Malaysia . Also Maltec-T is our very own manufacturer for RTD Sensor. Visit us here.
Heating element Info 2
Thick film technology: Heating elements for high-temperature furnaces are often made of exotic materials, including platinum, molybdenum disilicide, molybdenum (vacuum furnaces) and silicon carbide. Silicon carbide igniters are common in gas ovens. dpstar is a leading manufacturer and supplier in Malaysia . Visit our webpage.
Thermocouple Info 2
Thermocouples are a widely used type of temperature sensor for measurement and control, and can also convert a temperature gradient into electricity. Commercial thermocouples are inexpensive, interchangeable, are supplied with standard connectors, and can measure a wide range of temperatures. In contrast to most other methods of temperature measurement, thermocouples are self powered and require no external form of excitation. The main limitation with thermocouples is accuracy; system errors of less than one degree Celsius (°C) can be difficult to achieve. dpstar is in the top manufacturer and supplier in Malaysia . Our product thermocouple is created by dpstar Maltec-T .
Cartridge heater 2
dpstar Cartridge heaters are available in low, medium and high watt densities with internally externally connected leads. We also manufacture Split type cartridge heaters for high temperature applications. We built every technically possible heaters as per to our customers requirement. dpstar is a top supplier and manufacturer in Malaysia . Visit us at dpstar.
Immersion heater Info 2
The electric immersion heaters are used for the corrosive chemical heating in industrial applications. Various configurations are available, such as open tank, screw plug and flange type. The sheath materials can be constructed from a wide variety to ensure long life regardless of the chemistry. Materials include: fluoropolymer, quartz, titanium, 316 stainless steel, 304 stainless steel and plain steel. Sizes from as small as 100 watts for laboratory environments up to 54,000 watts (flange heater up to 270,000 watts) for industrial applications are available. Many standard configurations are available from stock. Quick lead times are also available for custom made heaters. Heaters are compliance to UL,CSA and CE marks. dpstar is Malaysia top supplier and manufacturer for immersion heater . Visit us here.
Friday 19 June 2015
Temperature Controller
Process and temperature controllers are powerful process control tools, but they offer very simple operation. Process controllers take a signal from a temperature device, such as a thermocouple or RTD, or from a pressure/ flow/ level sensor, and maintain a setpoint using an output signal. dpstar provides the best temperature controller because of their name for being Malaysia top manufacturer and suppliers. Visit us at www.dpstar.com.my.
RTD Sensor
resistance temperature detectors (RTDs), are sensors used to measure temperature by correlating the resistance of the RTD element with temperature. Most RTD elements consist of a length of fine coiled wire wrapped around a ceramic or glass core. The element is usually quite fragile, so it is often placed inside a sheathed probe to protect it. The RTD element is made from a pure material, typically platinum, nickel or copper. dpstar is a manufacturer and supplier that is famous for RTD Sensor due to the high quality of production. Maltec T the manufacturer produces high quality RTD Sensor. Visit us at www.dpstar.com.my.
Heating Element
Molybdenum disilicide: Molybdenum disilicide (MoSi2) an intermetallic compound, a silicide of molybdenum, is a refractory ceramic primarily used in heating elements. It has moderate density, melting point 2030 °C, and is electrically conductive. At high temperatures it forms a passivation layer of silicon dioxide, protecting it from further oxidation. dpstar is a manufacturer and supplier in Malaysia that manufacture many heating elements. dpstar is one of the top companiese in Malaysia. Visit us at www.dpstar.com.my
Thermocouple
A Thermocouple is a sensor used to measure temperature. Thermocouples consist of two wire legs made from different metals. The wires legs are welded together at one end, creating a junction. This junction is where the temperature is measured. When the junction experiences a change in temperature, a voltage is created. dpstar is the best in Malaysia in thermocouple and Maltec-H is the manufacturer for dpstar. dpstar is also the top supplier in Malayisa. Vist us at www.dpstar.com.my.
Cartridge heater (Insulation)
Insulation is used to prevent the Nichrome coil to contact the sheath. If such event happened, it would ground the resistance and potentially produce a catastrophic short-circuit, resulting in a melted sheath and a major equipment failure. Damage can be mitigated by installing a ground fault interuping circuit. To prevent the coil from touching the sheath, the coil is inserted into the sheath, and immediately filled with Magnesium Oxide (MgO). To ensure the MgO fills the empty space between the sheath and the coil, the cartridge heater is vibratory filled. dpstar manufacturer and supplier in Malaysia cartridge heater is high quality and cost saving. For more info visit us at www.dpstar.com.my.
Immersion heater
dpstar Industries has over 6 years of experience in the application, design and manufacturer of robust tubular immersion heaters and process assemblies. We have thousands of standard designs for quick field replacements and convenient ordering. dpstar also has extensive experience with custom designed electric immersion heaters for tank, reservoir and circulation flow applications. dpstar is Malaysia famous company which is a manufacturer and supplier of immersion heater . For more info visit us here .
Monday 15 June 2015
Hand Tools Series 164 : Locking Pliers & Series 168 : Preset Torque Screwdriver
Please visit us at : http://www.dpstar.com.my for more info
Hand Tools Series 151 : T-Handle Screwdriver / Series 156 : Samurai Pliers
Please visit us at : http://www.dpstar.com.my for more info
Hand Tools Series 1248 : Specialist Series Adjustable Wrench
Please visit us at : http://www.dpstar.com.my for more info
Tuesday 9 June 2015
HOT BEST SELLING !!!
Thermocouples
A Thermocouple is a sensor used to measure temperature. Thermocouples consist of two wire legs made from different metals. The wires legs are welded together at one end, creating a junction. This junction is where the temperature is measured. When the junction experiences a change in temperature, a voltage is created.There are many types of thermocouples, each with its own unique characteristics in terms of temperature range, durability, vibration resistance, chemical resistance, and application compatibility. Type J, K, T, & E are “Base Metal” thermocouples, the most common types of thermocouples.Type R, S, and B thermocouples are “Noble Metal” thermocouples, Thermocouples are known for their versatility as temperature sensors therefore commonly used on a wide range of applications - from an industrial usage thermocouple to a regular thermocouple found on utilities and regular appliances. dpstar provides many years of high quality Malaysia manufacturing, research and product development for your temperature sensing needs. dpstar manufacturers a tremendous selection of general application, mineral insulated metal sheathed, base metal, high temperature, surface temperature and multipoint thermocouples. dpstar famous Maltec-T is one of the largest leading manufacturer they produce high quality thermocouple and there are many other variety to choose from at www.dpstar.com.my.
Immersion Heater
The electric immersion heaters are used for the corrosive chemical heating in industrial applications. Various configurations are available, such as open tank, screw plug and flange type. The sheath materials can be constructed from a wide variety to ensure long life regardless of the chemistry. Materials include: fluoropolymer, quartz, titanium, 316 stainless steel, 304 stainless steel and plain steel. Sizes from as small as 100 watts for laboratory environments up to 54,000 watts (flange heater up to 270,000 watts) for industrial applications are available. Many standard configurations are available from stock. Quick lead times are also available for custom made heaters. Heaters are compliance to UL,CSA and CE marks. Many variety of immersion heater is available. Visit us at www.dpstar.com.my
Sunday 7 June 2015
Infrared Silica Quartz Heaters
Infrared Silica Quartz Heaters
Straight long wave infrared rays can be easily arranged to fall on an object by use of a reflection plate. If the cross-section of the reflection plate is designed in parabolic shape, most of the reflected rays will go in parallel direction to heat the object.
Aluminum plate has excellent reflective power, Stainless plate is slightly inforior to aluminum plate while stainless plate must be used where corrosive gas emerges.
There is 30% difference between the use of parabolic reflection plate and a plane type. Therefore a parabolic reflection plate should be used whenever it is possible.For maintaning the efficiency of the reflector cleaning must be done.
Why pick us ? We are a leading manufacturer in Malaysia and was established in 1996. Since our inception we have grew to become a top supplier, facilitating our valued clients through our offices located in northern, central and southern part of west Malaysia also our products that we are selling are high quality and certified electrical heaters. Such as Industrial Heaters,Tubular Heater,Ceramic Bobbin Heater,Duct Heater,Cartridge Heater,Finned Tubular Heater,Circulation Heater,Infrared Silica Quartz Heater,Teflon Immersion Heater,Flange Immersion Heater,and etc. Our products are only UL Certified,UKAS,ISO,Standards and etc. Visit us at www.dpstar.com.my
Black Infrapara Ceramic Heater
Black Infrapara Ceramic Heater
- Unique ceramic heater - selected ceramics with high thermal durability, mechanical strength and good electrical insulation. High quality Nichrome wire is used
- High emissivity
- Quick thermal response, high thermal efficiency
- Easy control to radiate favourable wave lengths for different target materials
- 1-10 times more speedy than ordinary heaters
- Uniform temperature distribution
- Electric power may be saved up to 50%, production yield may be raised 30% up
- Oven volume reduceable to one half or even less.Maintenance or replacement of existing old-fashioned heat pipes in ovens is easy
- Free from dust contamination. No fire flame appears during heating process
- High safety
Applications
- Heating plastic films and sheets in various forming applications
- Packaging
- Softening of plastic sheets before embossing
- Gelling paste coats on fabrics
- Hardening of synthetic threads
- Activation of thermal adhesives
- Drying synthetic emulsions
- Heating of paper pulp
- Thermal hardening of lacquered paper and cardboard
- Drying of skins & spray-coated leather
- Quick drying of gummed & glued paper
- Drying and burning-in of protective varnish in cans & tubes
- Drying and burning-in of lacquered sheet-metal parts
- Burning-in of powder coatings
- Drying the glaze on ceramic tiles
- Quick hardening of cement
- Tempering layered glass
- Preheating the welding seams in pipe construction
- Adherence of sound-absorbing mats in the consumer goods and automobile industries
- Heating climatic chambers
- Drying fabrics
- Accelerating glue curing
- Hardening of epoxy resins
- Various food applications including baking, drying, heating,warming & melting
Why pick us ? We are a leading manufacturer in Malaysia and was established in 1996. Since our inception we have grew to become a top supplier, facilitating our valued clients through our offices located in northern, central and southern part of west Malaysia also our products that we are selling are high quality and certified electrical heaters. Such as Industrial Heaters,Tubular Heater,Ceramic Bobbin Heater,Duct Heater,Cartridge Heater,Finned Tubular Heater,Circulation Heater,Infrared Silica Quartz Heater,Teflon Immersion Heater,Flange Immersion Heater,and etc. Our products are only UL Certified,UKAS,ISO,Standards and etc. Only at www.dpstar.com.my
Erema Silicon Carbide Heating Element
Erema Silicon Carbide Heating Element
dpstar heating elements, composed of high-purity, recrystallized silicon carbide, have earned the reputation as the world’s leading heating elements. These elements are widely used as high-temperature heat sources for electric furnaces and for the firing of ceramic capacitors, ferrites and other electronic components that are commonly used in mobile phones and computers.
EREMA silicon carbide (SiC) heating elements are manufactured by TOKAI Konetsu Kogyo Co., Ltd. (TKK) /JP, the world’s largest manufacturer of SiC heating elements. TKK believes that the trend of energy efficiency is basically the same worldwide. “Energy saving” and “sustainability” are globally becoming very important in today’s business.
EREMA silicon carbide (SiC) heating elements are manufactured by TOKAI Konetsu Kogyo Co., Ltd. (TKK)/JP, the world’s largest manufacturer of SiC heating elements. TKK believes that the trend of energy efficiency is basically the same worldwide. “Energy saving” and “sustainability” are globally becoming very important in today’s business. TKK has been manufacturing the EREMA SiC heating elements since 1936 at two locations in Japan and China. These elements are the most energy-efficient, cost-effective and versatile heating elements on the market. One of TKK’s latest developments is the new EREMA Eco Heater (EH). These elements use less power than conventional elements, and the resulting cost saving over their lifetime can exceed in many applications their purchase price. Typical pay back periods can be as short as 12 months, depending on the application. EREMA SiC EH elements are designed with specially formulated cold ends which significantly reduce the heat loss from the terminals concentrating the heat where needed in the furnace. Reduced heat losses result in lower power consumption saving energy costs also helping to reduce the furnace carbon footprint by lowering the greenhouse gas emission – protecting the environment.
Why pick us ? We are a leading manufacturer in Malaysia and was established in 1996. Since our inception we have grew to become a top supplier, facilitating our valued clients through our offices located in northern, central and southern part of west Malaysia also our products that we are selling are high quality and certified electrical heaters. Such as Industrial Heaters,Tubular Heater,Ceramic Bobbin Heater,Duct Heater,Cartridge Heater,Finned Tubular Heater,Circulation Heater,Infrared Silica Quartz Heater,Teflon Immersion Heater,Flange Immersion Heater,and etc. Our products are only UL Certified, UKAS,ISO,Standards and etc. Visit us for more outstanding information at http://www.dpstar.com.my
Subscribe to:
Posts (Atom)